Skip to content

wtdbg2

Description

wtdbg2 is a fast de novo assembly tool for long-read sequece data produced by PacBio or Oxford Nanopore Technologies sequencers.

License

Free to use and open source under GNU GPLv3.

Available

Version on CSC's Servers

  • Puhti: 2.5

Usage

In Puhti, the wtdbg2 is activated by loading the biokit environment.

module load biokit

After that you can use commands wtdbg2 asembler and wrpoa-cns consenser commands. wtdbg2 assembles raw reads and generates the contig layout and edge sequences in a file prefix.ctg.lay.gz. Executable wtpoa-cns takes this file as input and produces the final consensus in FASTA.

A typical workflow looks like this:

wtdbg2 -x rs -g 4.6m -t 16 -i reads.fa.gz -fo prefix
wtpoa-cns -t 16 -i prefix.ctg.lay.gz -fo prefix.ctg.fa

In the wtdbg2 command -g is the estimated genome size and -x specifies the sequencing technology, which could take value rs for PacBio RSII, sq for PacBio Sequel, ccs for PacBio CCS reads and ont for Oxford Nanopore. This option sets multiple parameters and should be applied before other parameters. When you are unable to get a good assembly, you may need to tune other parameters as described in the wtdbg2 manual.

In the case of any large ( more than 10 Mb) genomes, wtdbg2 assembly process can take several hours or days. In Puhti, this large tasks shoud always be executed as batch jobs.

Below is a sample batch job file for assembling C. elegans genome.

The sample dataset was downloaded from ENA database with commands:

enaDataGet SRR5439404 -f fastq
mv SRR5439404/SRR5439404_subreads.fastq.gz ./

The actutal assembly task was executed with the batch job below:

#!/bin/bash
#SBATCH --job-name=wtdbg2
#SBATCH --account=<project>
#SBATCH --time=12:00:00
#SBATCH --ntasks=1
#SBATCH --nodes=1
#SBATCH --output==wtdbg2_out_32_%j
#SBATCH --error=wtdbg2_err_32_%j
#SBATCH --cpus-per-task=32
#SBATCH --mem=64G
#SBATCH --partition=small

module load biokit

wtdbg2 -x rs -g100m -t $SLURM_CPUS_PER_TASK -i SRR5439404_subreads.fastq.gz -fo c_elegas_test

wtpoa-cns -t $SLURM_CPUS_PER_TASK -i c_elegas_test.ctg.lay.gz -fo c_elegabs.ctg.fa
In the example above could be replaced with your project name. You can use csc-workspaces to check your Puhti projects. Maximum running time is set to 12 hours (--time=12:00:00). As wtdbg2 uses threads based parallelization, the process is considered as one job that should be executed within one node (--ntasks=1, --ntasks=1). The job reserves 32 cores --cpus-per-task=32 that can use in total up to 64 GB of memory (--mem=64G). Note that the number of cores to be used needs to be defined in wtdbg2 and wtpoa-cns commands too. That is done with option -t. In this case we use $SLURM_CPUS_PER_TASK variable that contains the cpus-pre-task value ( we could as well use -t 32 but then we have to remember to change the value if number of the reserved CPU:s is changed).

The job is submitted to the to the batch job system with sbatch command. For example, if the batch job file is named as wtdbg2_job.sh then the submission command is: 

sbatch wtdbg2_job.sh
More information about runnig batch jobs can be found from the batch job section of the Puhti user guide.

Manual